FAQ .: Rechercher .: Membres .: Groupes .:  S’enregistrer .:  Profil .: Se connecter pour vérifier ses messages privés .: Connexion 
A new high pressure

 
Poster un nouveau sujet   Répondre au sujet    forum guilde bad clown Index du Forum » Ambassade » Règlement
Sujet précédent :: Sujet suivant  
Auteur Message
DMT


Hors ligne

Inscrit le: 09 Oct 2018
Messages: 29

MessagePosté le: Mar 9 Oct - 12:01 (2018)    Sujet du message: A new high pressure Répondre en citant
Before welding the crushing equipment Rays Kevin Kiermaier Jersey , you should pay attention to the following tips.

1) You should thoroughly clean the parts to be welded before welding.

2) The effect of hot welding is better than the effect of cold welding. Therefore, when the major parts are welded, you may try to use the hot welding. You can heat the weldment to 100 ° C to 700° C in advance.

3) In the conditional case, you should use downhand welding which will be good for the quality of the weld and is conducive to the operation.

4) Electrode diameter and current size of the welding rod should be selected depending on the thickness of the weldment, the surrounding temperature and welding location. The model of the welding rod should be selected according to the materials of the welment and related technologies.

The most common method of the weld is the vibrating surfacing and carbide hardfacing method. The practice has proved that using the high current for welding can improve the quality of welding and speed the welding. But the current should not be too high. Sometimes, low current is also be required. The overcurrent will cause the overheating of the welding rod core. Thecovered electrode will be dropped early, which will increase the spatter and burning and reduce the stability of the arc so that the welding becomes difficult. At the same time, both sides of welding will be undercut. The roots will be too thin and burn easily. For the alloy steel, if the metal structure is overheating, the metal of the weld zone is perishable and the mechanical strength is reduced. If the current is too small, the penetration depth will be not enough. It is also easily to lead to impermeable weld and bad melting. At the same time, due to the small heat of the arc, the condensation of the melt injection is rapid, which will form the weld central residue and stomata.

When the <"http:www.china-hxjqp4">impact crusher is required, you should be strict with the implementation of the operation law of the equipment, maintenance procedures and planned maintenance system to ensure the maintenance quality. Any sloppy thinking will bring loss and impact of different level. The contact of mating surfaces of the journal and the bearing is poor will cause uneven load distribution of unit area and an increase of additional load to accelerate the wear parts. Therefore, we must conscientiously implement the maintenance of equipment, really do good job in the equipment use, care and maintenance, inspect and repair the crusher in a timely manner in order to reduce the wear and tear of parts and extend the service life of the machine.

The processing requirements of the non-metal processing and metal mineral processing are different. The dissemination size of the useful ingredients in the metal mineral is fine, which must be grinded to a certain grain size. In this way ,the ore can be sorted out through the <"http:www.hxjqchinan28">ore beneficiation method. For the processing of the non-metallic minerals, some product with narrow grain size is required as the finished product. For example, the precision casting sand size requirement is between 1 ~ 0.5mm and 0.5-0.28mm; the glass raw materials quartz sand particle size requirement is between 0.71mm and 0.105mm; the quartz glass industry with high purity quartz sand particle size requirement is between 0.18mm and 0.105mm; the corundum sand size requirement in abrasive industry is between 1.4mm and 0.105mm. The non-metallic mineral finished products are very strict with the requirements for iron content. In addition, some non-metallic mineral processing also has finished grain shape, such as abrasives industry, precision casting sand industry.
VA high pressure small vane axial blower finally resolves the problem of boosting air flow in long ventilation ducts of today's large residential houses. VA high pressure small vane axial blower finally resolves the problem of boosting air flow in long ventilation ducts of today's large residential houses.

For a long time the efficient ventilation of remote rooms in the large houses could be done only with two independent air supply sources (like a furnace). Ventilating ductwork in contemporary large houses becomes so long and elaborated that even a high pressure furnace fan couldn't generate enough static pressure to blow through the whole length of such a duct. The existing low pressure booster duct fans, even though compact enough to be installed in-line in the house ventilation ductwork, still do not provide enough booster pressure airflow. The usual solution to this problem was installation of two independent furnaces with different air ducts, which is rather expensive option.

A new high pressure (up to 1.5" WG) small vaneaxial Series VA fan is an ideal booster fan for prolonged ducts. Unlike inline centrifugal ventilator, that also generates rather high pressure, the air comes out not from a peripheral outlet ring area, but distributes evenly across its outlet opening like in true axial blowers.

The other advantages of VA Series vaneaxial ventilators is their intrinsic spark-resistant construction because of all-aluminum construction; quiet operation of true vaneaxial design; lower energy consumption due to efficient wheel design.

Eight different sizes from 6" DIA to 10" DIA offer wide performance range for any ventilation duct design. Direct drive design ensures long live, maintenance-free operation. Explosion proof motors are available too, as well as sliding dampers, various mounting options, additional sound isolation.

Another high pressure in-line fan developed by American Blowers Co. is Mix Flow Fan. Mixed Flow fan. Cheap Jerseys   Cheap Jerseys China   Cheap Jerseys China   Cheap Jerseys Online   Cheap Jerseys Free Shipping   Cheap Authentic Jerseys   Cheap NFL Jerseys Wholesale   Cheap Football Jerseys   Wholesale Jerseys   Wholesale Jerseys From China 



Auteur Message
Publicité




MessagePosté le: Mar 9 Oct - 12:01 (2018)    Sujet du message: Publicité
PublicitéSupprimer les publicités ?

Poster un nouveau sujet   Répondre au sujet    forum guilde bad clown Index du Forum » Règlement

Page 1 sur 1
Toutes les heures sont au format GMT + 2 Heures

Montrer les messages depuis:

  

Sauter vers:  

Index | Panneau d’administration | Creer un forum | Forum gratuit d’entraide | Annuaire des forums gratuits | Signaler une violation | Conditions générales d'utilisation
Powered by phpBB © 2001, 2018 phpBB Group Traduction par : phpBB-fr.com
Colosseum by Scott Stubblefield